How To Change Cigarette Lighter To Turn On/off With Ignition Youtube

Download Article

Download Article

Cigarette lighter sockets are very useful for operating lighters and many other electrical gadgets, but they wear out over time. Fortunately, removing the socket is a relatively like shooting fish in a barrel procedure that doesn't require mechanical feel or many tools. To start, shut off the motorcar and fuse to stop ability from reaching the lighter. Then, yous can get a socket out of the dashboard or the lower half of your vehicle by removing interior panels. Remove a lighter socket to replace it with a new one or an alternative to charge any device you need while driving.

1. one

   Turn off the automobile'south engine using the ignition key. Equally long as yous have your key out of the ignition, you are fine. Don't try touching the lighter wires or the fuses while the auto is running. Make sure the radio isn't running since the cigarette lighter socket often shares a fuse with the other components in the middle of your car.^[1]

   • Stay safe by turning off the vehicle before handling any wires or connected components. If yous don't have the proper precautions, you could finish up sticking metal within the socket while it is notwithstanding active.

2. two

   Locate the fuse box in the vehicle. The fuse box typically is underneath the hood or the dashboard. Bank check inside the glove box on the passenger's side if you don't see it anywhere else. It looks like a covered blackness box with a bunch of colored plugs within of it and is sometimes labeled.^[2]

   • If y'all tin't find the fuse box, consult your owner's manual for more than information. Some vehicles fifty-fifty accept multiple fuse boxes controlling different parts.

   Advertisement

3. 3

   Remove the cigarette lighter fuse with a pair of pliers. Look for letter labels almost the fuses or on the fuse box cover. You lot can normally remove a fuse box cover by hand, only you may also need a Phillips head screwdriver for yours. Once you locate the fuse responsible for the cigarette lighter, use needle-nose pliers to pull it out of the box. Set the small fuse aside in a prophylactic location until y'all're ready to put it back.^[3]

   • If y'all don't meet a fuse box diagram inside your vehicle, bank check for 1 in the owner'southward manual.

4. 4

   Use a multimeter to make certain y'all deactivated the lighter. A multimeter is a handheld device that detects electrical currents. To test the lighter, you have to kickoff find an exposed slice of metal in your vehicle, such as a bolt on the door. Agree the blackness probe to the piece of metal, then touch the red probe to the cigarette lighter socket. If the meter moves, the socket still has an agile current and isn't safety to touch.^[4]

   • Y'all can get multimeters at well-nigh hardware or auto parts stores.
   • If the meter picks up electrical activity, check the fuses again. Yous may have removed the wrong one by accident.

Advertisement

1. 1

   Employ a hook to reach the slots in the cigarette lighter. Await inside the cigarette lighter socket to detect the small openings effectually its sides. These slots let you to grip the socket, but you demand a strong piece of metal to remove it. The easiest tool to utilize is a lighter socket removal tool, which looks like a small metal bar with a pair of prongs on the end. Fit the prongs into the slots to begin removing the socket.^[five]

   • You can find socket removal tools online. Likewise, ask at your local motorcar parts stores for alternatives.
   • If yous don't have a socket removal tool, find something similar that fits inside the lighter socket. For example, y'all could use a metal hook or bend a metal glaze hanger to latch onto the socket slots.

2. 2

   Turn the lighter socket clockwise to loosen it. The socket rests inside a 2d metal tube on your vehicle. Dissimilar most other connectors in the vehicle, y'all accept to spin the socket clockwise to disconnect it from the tube. Use the removal tool to loosen the socket past spinning it in place. When the socket is loose, it turns freely and may even pop out of the dashboard.^[6]

   • The socket is often a fiddling stubborn at first, and so put some force into turning it. You lot may need to get a pair of pliers to turn the socket by hand.

3. 3

   Popular off the dashboard panel if you tin't remove the socket. If the socket loosens but doesn't pop out, pry off the console effectually information technology. Check the panel get-go past trying to remove it with your hands. If you tin't remove information technology by hand, go a plastic pry tool and slide it underneath the panel. Work around the edges of the panel, gently prying it away from the rest of the car until yous are able to lift it and look behind it.^[7]

   • Shop online or visit your local hardware and auto parts stores for pry tools. Make sure you get plastic ones instead of metal to avoid damaging the car panel.
   • The cigarette lighter socket may still exist attached to the rest of the motorcar, so don't rip the panel off as soon every bit you detach information technology. This is especially truthful if the socket is virtually the radio, since the radio and climate control wires most likely likewise adhere to the panel.

4. iv

   Unplug the wire connector if it is still attached to the socket. Lay the panel flat and so you are able encounter any wires backside it. Detect the back end of the socket and check information technology for a wire attachment. If the lighter socket has a wire in it, squeeze the plastic connector, so pull it abroad from the socket. The connector is typically a circular piece of plastic with a brilliant coloring like blue.^[8]

   • The connector is usually easy to remove by hand. Y'all may demand to pull information technology with a trivial fleck of force to pop information technology off of the socket.
   • Y'all tin can remove other connectors on the panel. If you removed the plate around the radio, for instance, the radio controls besides have plastic connectors. You don't demand to remove those connectors, just unplugging them gives you a little more than room to maneuver.

5. five

   Pull and turn the socket as needed to terminate removing it. Reach backside the panel to push the lighter socket toward you. Most sockets pop out of the dashboard panel without much difficulty. You may also need to spin the socket to loosen it a little more than before it pops out. Catch the front end terminate of the socket to turn it by hand until it slides out of the panel.^[9]

   • Try to avoid forcing the socket out. It is pretty easy to remove, then if information technology feels stuck, chances are it is withal attached to the auto. Check for a wire connector and rotate the socket clockwise until it loosens.
   • If y'all tin can't remove the socket and know that you cleared away any wires, apply pliers to plough it until it loosens.

Advertisement

1. i

   Remove the side panel to admission the back cease of the lighter. If the lighter is near the gear stick in your vehicle, attain into the sleeping room underneath the stick to become to the socket. Move the seats back as far as possible, and so pull off 1 of the plastic panels in the center part of your automobile. If you can't become the panel off by manus, use a plastic pry tool to wedge the panel off of its mount. Work slowly around the border of the panel until you are able to slide it off.^[10]

   • Get pry tools by shopping online or visiting hardware or auto parts stores.
   • The panels you demand to remove are underneath the gear stick and very noticeable. As long as you remove 1 panel on the chamber housing the gear controls, yous tin reach the lighter.

2. 2

   Plough the wire connector counterclockwise to pop it off the socket. Await for a plastic wire connector on the dorsum end of the lighter socket. Information technology has a light-green and a blackness wire coming out of it, connecting the socket to the residuum of the motorcar. To remove it, grip it lightly between your fingers and rotate information technology counterclockwise. Information technology comes free afterwards about a quarter of a turn, and then turn information technology slowly to avert pulling the wires.^[11]

   • The wire connector looks like a round plug. It is often gray, but it might be a different color in your machine. The plug always has a pair of wires, greenish and black, that make information technology recognizable.
   • Some cigarette lighter sockets take 2 different plugs. One plug on the side holds the green ground wire while the other plug in the eye holds the black power wire. Remove both plugs if your vehicle has them.

3. three

   Have the clips off the electrical connector to remove it. The next component on the lighter socket looks like a round, gray cap with an opening holding another wire. Information technology has a pair of fly-like clips on the side. Grab both of the clips and gently pull them away from the cigarette lighter to slide the connector off of it.^[12]

   • The electrical connector has a blood-red wire supplying ability to lighter. Set the connector aside to avoid damaging the wire.

4. 4

   Employ a socket wrench to remove the nut holding the lighter in place. Removing the connectors exposes the back end of the lighter socket. The nut is a metallic band with an opening in the center and it fits over the back terminate of the socket. The easiest mode to remove it is by fitting a ¹⁄_sixteen  in (0.16 cm) socket wrench over it. Twist it counterclockwise a few times until it is loose enough to twist off past hand.^[13]

   • Finish removing the nut by continuing to turn it counterclockwise past manus. Slide it off of the socket and fix it aside.

5. five

   Take the light housing off to remove the cigarette lighter. A second metal cylinder, the light housing, covers the back end of the lighter socket. All you take to exercise is slide information technology off to remove it. Removing it leaves the lighter socket exposed, and then simply pull it out of the hole in the plastic.^[14]

Ad

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertisement

• Every auto is a little different, and then the exact socket removal process may differ slightly depending on your vehicle. Refer to your owner's manual for more specific instructions.

• If your cigarette lighter socket stops working, bank check the fuse beginning. Fuses are more probable to accident out than the socket and are likewise cheaper and easier to replace.

• Supercede a cigarette lighter socket past buying a new one, then sliding it into the slot that holds it in place on your vehicle.

Thank you for submitting a tip for review!

Advertisement

• Electrical wires connect to the lighter socket, and touching it while the wires are active could issue in an electric stupor. Always shut off the car, remove the fuse, and test the socket with a multimeter to avoid trouble.

Advertisement

Things You lot'll Need

• Ignition key
• Fuse puller or needle-nose pliers
• Owner's manual
• Multimeter

• Metallic hook or socket removal tool
• Plastic pry tool

• Plastic pry tool
• ¹⁄_sixteen  in (0.sixteen cm) socket wrench or pliers

About This Article

Thanks to all authors for creating a page that has been read 102,000 times.

Did this commodity assist you lot?

Source: https://www.wikihow.com/Remove-a-Cigarette-Lighter-Socket

Posted by: mitchelltheinder1941.blogspot.com

Share this post